L298 Dual H-Bridge Motor Driver
30,50 € Iva inclusa
SEEEDSTUDIO

L298 Dual H-Bridge Motor Driver

SEEEDSTUDIO
L298 Dual H-Bridge Motor Driver
L298 Dual H-Bridge Motor Driver
COD: 302476
COD.MEPA: 302476CS

Descrizione

Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the connection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage.

- Light weight, small dimension
- Super driver capacity
- FWD protection
- Heavy load Heat sink
- 2 current probe port
- Power selection switch
- 4 pull up resistor switch
- 2 DC motor/ 4 coil dual phrase stepper motor output
- Motor direction indication LED
- 4 standard mounting hole

Applications:
MCU controlled vehicle
Wheel robot
Specification:
Driver: L298
Driver power supply: +5V~+46V
Driver Io: 2A
Logic power output Vss: +5~+7V (internal supply +5V)
Logic current: 0~36mA
Controlling level: Low -0.3V~1.5V, high: 2.3V~Vss
Enable signal level: Low -0.3V~1.5V, high: 2.3V~Vss
Max power: 25W (Temperature 75 cesus)
Working temperature: -25C~+130C
Dimension: 60mm*54mm
Driver weight: ~48g
Other extensions: current probe, controlling direction indicator, pull-up resistor switch, logic part power supply.
30,50 € Iva inclusa
Su ordinazione
Il prodotto non è presso il nostro magazzino e i tempi di consegna dipendono dal nostro fornitore: contattaci per dei tempi di consegna più precisi Su ordinazione:
Il prodotto non è presso il nostro magazzino e i tempi di consegna dipendono dal nostro fornitore: contattaci per dei tempi di consegna più precisi

Descrizione

Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the connection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage.

- Light weight, small dimension
- Super driver capacity
- FWD protection
- Heavy load Heat sink
- 2 current probe port
- Power selection switch
- 4 pull up resistor switch
- 2 DC motor/ 4 coil dual phrase stepper motor output
- Motor direction indication LED
- 4 standard mounting hole

Applications:
MCU controlled vehicle
Wheel robot
Specification:
Driver: L298
Driver power supply: +5V~+46V
Driver Io: 2A
Logic power output Vss: +5~+7V (internal supply +5V)
Logic current: 0~36mA
Controlling level: Low -0.3V~1.5V, high: 2.3V~Vss
Enable signal level: Low -0.3V~1.5V, high: 2.3V~Vss
Max power: 25W (Temperature 75 cesus)
Working temperature: -25C~+130C
Dimension: 60mm*54mm
Driver weight: ~48g
Other extensions: current probe, controlling direction indicator, pull-up resistor switch, logic part power supply.

Recensioni

Hai comprato questo prodotto? Fai sapere agli altri cosa ne pensi.
Valuta