Contact us Acquisto Rapido

Adafruit 1.8" 18-bit Color TFT Shield w/microSD and Joystick

Disponibilità limitata

Descrizione

Codice: 302338
Adafruit 1.8" 18-bit Color TFT Shield w/microSD and Joystick
€ 33,60
(+ IVA 22%)
PREZZO IVA INCLUSA:
O

Diventa il primo a recensire il prodotto

Adafruit 1.8" 18-bit Color TFT Shield w/microSD and Joystick

Muovi il mouse sull'immagine per ingrandirla dove disponibile

Dettagli

This lovely little shield is the best way to add a small, colorful and bright display to any project. We took our popular 1.8" TFT breakout board and remixed it into an Arduino shield complete with microSD card slot and a 5-way joystick navigation switch (with a nice plastic knob)! Since the display uses only 4 pins to communicate and has its own pixel-addressable frame buffer, it can be used easily to add a display & interface without exhausting the memory or pins.

The 1.8" display has 128x160 color pixels. Unlike the low cost "Nokia 6110" and similar LCD displays, which are CSTN type and thus have poor color and slow refresh, this display is a true TFT! The TFT driver (ST7735R) can display full 18-bit color (262,144 shades!). And the LCD will always come with the same driver chip so there's no worries that your code will not work from one to the other.

The shield has the TFT display soldered on (it uses a delicate flex-circuit connector) as well as a ultra-low-dropout 3.3V regulator and a 3/5V level shifter so its safe to use with 5V Arduinos. We also had some space left over so we placed a microSD card holder (so you can easily load full color bitmaps from a FAT16/FAT32 formatted microSD card) and a 5-way navigation switch (left, right, up, down, select). The microSD card is not included.

If you just want to display text, shapes, lines, pixels, etc the shield uses pins 13, 11, 10 and 8. If you'd like to add the navigation switch, it uses Analog 3 (all 5 switches are connected using a clever resistor trick to permit all the switches to share one analog pin). For the microSD card, you'll also give up Digital 12 and 4.

Comes as a fully assembled and tested shield with the display, microsd card holder and nav switch with knob as well as a stick of 0.1" header. To finish up and use, you will need to solder on the header onto the shield PCB, a quick 10 minute task.

Of course, we wouldn't just leave you with a datasheet and a "good luck!" - we've written a full open source graphics library that can draw pixels, lines, rectangles, circles, text and bitmaps as well as example code and a wiring tutorial. The code is written for Arduino but can be easily ported to your favorite microcontroller!


Specifications:
1.8" diagonal LCD TFT display
128x160 resolution, 18-bit (262,144) color
ST7735R (datasheet) controller with built in pixel-addressable video RAM buffer
4 wire SPI digital interface
Built-in microSD slot - uses 2 more digital lines
5V compatible! Use with 3.3V or 5V logic Arduinos
Onboard 3.3V @ 150mA LDO regulator
2 white LED backlight, transistor connected. Defaults to 'on' but can be connected to a digital pin for PWM or simply turning off
Comes with header, requires soldering!

Il CIG e il CUP sono richiesti per assicurare la tracciabiltà dei flussi finanziari nei lavori pubblici.
Art. 3 della L. 13/08/2010, n. 136 (pubblicata sulla Gazzetta Ufficiale n. 196 del 23/08/2010 - serie generale).
Gazzetta Ufficiale: www.interno.it/mininterno/export/sites/default/it/assets/files/19/00222_LEGGE_13_agosto_2010x_n._136.pdf

CIG = codice identificativo di gara
CUP = codice unico di progetto

N.B. Se l'ordine è composto da più articoli e si riferisce ad un unico CIG/CUP, i codici possono essere inseriti alla fine dell'operazione.

Scrivi una recensione

* Campi Obbligatori

Tag dei Prodotti

Usa gli spazi per separare i tags. Usa virgolette singole (') per le frasi.

Contatti
Newsletter
Iscriviti alla nostra newsletter e riceverai le nostre offerte esclusive: