ADAFRUIT
Small Reduction Stepper Motor - 5VDC 32-Step 1/16 Gearing
Small Reduction Stepper Motor - 5VDC 32-Step 1/16 Gearing
COD: 304818
COD.MEPA: 304818CS
COD.MEPA: 304818CS
Descrizione
This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with two mounting holes. There are only 32 step (11.25 degree) per revolution, and inside is a 1/16 reduction gear set. (Actually its 1/16.032 but for most purposes 1/16 is a good enough approximation) What this means is that there are really 32*16.032 steps per revolution = 513 steps! The shaft is flattened so its easy to attach stuff to it with a set-screw.
A perfect first stepper motor and works well with the Motor Shield for Arduino.
The gearing has a few side effects which are important to note. First, you can turn the stepper by hand but not as smoothly as an un-geared stepper. It also means you shouldn't use interleaved or micro-stepping to control or it will take forever to turn. Instead use single or double stepping. The torque is fairly high but its slower than un-geared steppers - we maxed out at about 50 RPM by over-driving it a bit with 9VDC. At 5V try to stick to under 25 RPM
To use with the Adafruit Motor Shield, connect red to ground (middle), orange and pink to one motor port (say M1) and blue and yellow to the other motor port (say M2). So in order, thats: orange - pink - red - blue - yellow. Then just use the example code that comes with the Adafruit Motor Shield library and set the constructor to Adafruit_StepperMotor *myMotor = AFMS.getStepper(513,motornum) and the speed at 5 RPM by calling motor->setSpeed(5). Otherwise, you can also wire it up with some transistors and use the Arduino Stepper library
TECHNICAL DETAILS:
Unipolar stepper with 0.1" spaced 5-pin cable connector
513 steps per revolution
1/16.032 geared down reduction
5V DC suggested operation
Weight: 37 g.
Dimensions: 28mm diameter, 20mm tall not including 9mm shaft with 5mm diameter
9" / 23 cm long cable
Holding Torque: 150 gram-force*cm, 15 N*mm/ 2 oz-force*in
Shaft: 5mm diameter flattened
Approx 42 ohm DC impedence per winding
A perfect first stepper motor and works well with the Motor Shield for Arduino.
The gearing has a few side effects which are important to note. First, you can turn the stepper by hand but not as smoothly as an un-geared stepper. It also means you shouldn't use interleaved or micro-stepping to control or it will take forever to turn. Instead use single or double stepping. The torque is fairly high but its slower than un-geared steppers - we maxed out at about 50 RPM by over-driving it a bit with 9VDC. At 5V try to stick to under 25 RPM
To use with the Adafruit Motor Shield, connect red to ground (middle), orange and pink to one motor port (say M1) and blue and yellow to the other motor port (say M2). So in order, thats: orange - pink - red - blue - yellow. Then just use the example code that comes with the Adafruit Motor Shield library and set the constructor to Adafruit_StepperMotor *myMotor = AFMS.getStepper(513,motornum) and the speed at 5 RPM by calling motor->setSpeed(5). Otherwise, you can also wire it up with some transistors and use the Arduino Stepper library
TECHNICAL DETAILS:
Unipolar stepper with 0.1" spaced 5-pin cable connector
513 steps per revolution
1/16.032 geared down reduction
5V DC suggested operation
Weight: 37 g.
Dimensions: 28mm diameter, 20mm tall not including 9mm shaft with 5mm diameter
9" / 23 cm long cable
Holding Torque: 150 gram-force*cm, 15 N*mm/ 2 oz-force*in
Shaft: 5mm diameter flattened
Approx 42 ohm DC impedence per winding
6,04 € Iva inclusa
Su ordinazione
Il prodotto non è presso il nostro magazzino e i tempi di consegna dipendono dal nostro fornitore: contattaci per dei tempi di consegna più precisi Su ordinazione:Il prodotto non è presso il nostro magazzino e i tempi di consegna dipendono dal nostro fornitore: contattaci per dei tempi di consegna più precisi
ACQUISTI PER LA PUBBLICA AMMINISTRAZIONE?
GUIDA ALL'ACQUISTO
CAMPUSTORE RISPONDE
Descrizione
This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with two mounting holes. There are only 32 step (11.25 degree) per revolution, and inside is a 1/16 reduction gear set. (Actually its 1/16.032 but for most purposes 1/16 is a good enough approximation) What this means is that there are really 32*16.032 steps per revolution = 513 steps! The shaft is flattened so its easy to attach stuff to it with a set-screw.
A perfect first stepper motor and works well with the Motor Shield for Arduino.
The gearing has a few side effects which are important to note. First, you can turn the stepper by hand but not as smoothly as an un-geared stepper. It also means you shouldn't use interleaved or micro-stepping to control or it will take forever to turn. Instead use single or double stepping. The torque is fairly high but its slower than un-geared steppers - we maxed out at about 50 RPM by over-driving it a bit with 9VDC. At 5V try to stick to under 25 RPM
To use with the Adafruit Motor Shield, connect red to ground (middle), orange and pink to one motor port (say M1) and blue and yellow to the other motor port (say M2). So in order, thats: orange - pink - red - blue - yellow. Then just use the example code that comes with the Adafruit Motor Shield library and set the constructor to Adafruit_StepperMotor *myMotor = AFMS.getStepper(513,motornum) and the speed at 5 RPM by calling motor->setSpeed(5). Otherwise, you can also wire it up with some transistors and use the Arduino Stepper library
TECHNICAL DETAILS:
Unipolar stepper with 0.1" spaced 5-pin cable connector
513 steps per revolution
1/16.032 geared down reduction
5V DC suggested operation
Weight: 37 g.
Dimensions: 28mm diameter, 20mm tall not including 9mm shaft with 5mm diameter
9" / 23 cm long cable
Holding Torque: 150 gram-force*cm, 15 N*mm/ 2 oz-force*in
Shaft: 5mm diameter flattened
Approx 42 ohm DC impedence per winding
A perfect first stepper motor and works well with the Motor Shield for Arduino.
The gearing has a few side effects which are important to note. First, you can turn the stepper by hand but not as smoothly as an un-geared stepper. It also means you shouldn't use interleaved or micro-stepping to control or it will take forever to turn. Instead use single or double stepping. The torque is fairly high but its slower than un-geared steppers - we maxed out at about 50 RPM by over-driving it a bit with 9VDC. At 5V try to stick to under 25 RPM
To use with the Adafruit Motor Shield, connect red to ground (middle), orange and pink to one motor port (say M1) and blue and yellow to the other motor port (say M2). So in order, thats: orange - pink - red - blue - yellow. Then just use the example code that comes with the Adafruit Motor Shield library and set the constructor to Adafruit_StepperMotor *myMotor = AFMS.getStepper(513,motornum) and the speed at 5 RPM by calling motor->setSpeed(5). Otherwise, you can also wire it up with some transistors and use the Arduino Stepper library
TECHNICAL DETAILS:
Unipolar stepper with 0.1" spaced 5-pin cable connector
513 steps per revolution
1/16.032 geared down reduction
5V DC suggested operation
Weight: 37 g.
Dimensions: 28mm diameter, 20mm tall not including 9mm shaft with 5mm diameter
9" / 23 cm long cable
Holding Torque: 150 gram-force*cm, 15 N*mm/ 2 oz-force*in
Shaft: 5mm diameter flattened
Approx 42 ohm DC impedence per winding
